FBI test Protocal?

FBI Test Protocal?

This is a discussion on FBI Test Protocal? within the Defensive Ammunition & Ballistics forums, part of the Defensive Carry Discussions category; What is it, you ask? Well, in case you don't know: Per the FBI's Annual Report of results of handgun ammunition testing. The FBI, after ...

Results 1 to 2 of 2
  1. #1
    Member Array Erik's Avatar
    Join Date
    Nov 2006
    Location
    USA
    Posts
    415
    What is it, you ask?

    Well, in case you don't know:

    Per the FBI's Annual Report of results of handgun ammunition testing.

    The FBI, after extensive research and consultation, established that a handgun bullet must consistently penetrate a minimum of 12 inches of tissue in order to reliably penetrate vital organs within the human target regardless of the angle of impact or intervening obstacles such as arms, clothing, glass, etc. Penetration of 18 inches is even better. Given minimum penetration, the only means of increasing wound effectiveness is to enlarge the permanent cavity. This increases the amount of vital tissues with a marginally placed shot, and increases the potential for quicker blood loss. This is important because, with the single exception of damaging the central nervous system, the only way to force incapacitation upon an unwilling adversary is to cause enough blood loss to starve the brain of its oxygen and/or drop blood pressure to zero. This takes time, and the faster haemorrhage can occur the better.

    The FBI ammunition test protocol is a series of practically oriented tests to measure a bullet's ability to meet these performance standards. The result is an assessment of a bullet's ability to inflict effective wounds after defeating various intervening obstacles commonly present in law enforcement shootings. The overall results of a test are thus indicative of that specific cartridge's suitability for the wide range of conditions in which law enforcement officers engage in shootings.

    The test media used by the FBI to simulate living tissue is 10% ballistic gelatin (Kind & Knox 250-A), mixed by weight. The gelatin is stored at 4x Centigrade (39.2x Fahrenheit) and shot within 20 minutes of being removed from the refrigerator. The temperature of the gelatin is critical, because penetration changes significantly with temperature. This specific gelatin mix was determined and calibrated by the U.S. Army Wound Ballistics Research Laboratory, Presidio of San Francisco, to produce the same penetration results as that obtained in actual living tissue. Each gelatin block is calibrated before use to ensure its composition is within defined parameters. The gelatin blocks for handgun rounds are approximately six inches square and 16 inches long. As necessary, additional blocks are lined up in contact with each other to ensure containment of the bullet's penetration. Each shot's penetration is measured to the nearest 0.25 inch. The projectile is recovered, weighed and measured for expansion by averaging its greatest diameter with its smallest diameter.

    The ammunition test protocol using this gelatin is composed of eight test events. In each test event, five shots are fired. A new gelatin block and new test materials are used for each individual shot. The complete test consists of firing 40 shots. Each test event is discussed below in order.

    All firing in these eight test events is done with a typical service weapon representative of those used by law enforcement. The weapon used is fully described in each test report.

    test Event l--Bare Gelatin

    The gelatin block is bare and shot at a range of ten feet measured from the muzzle to the front of the block. This test event correlates FBI results with those being obtained by other researchers, few of whom shoot into anything other than bare gelatin. It is common to obtain the greatest bullet expansion in this test. Rounds which do not meet the standards against bare
    gelatin tend to be unreliable in the more practical test events that follow.

    test Event 2--Heavy Clothing

    The gelatin block is covered with four layers of clothing: One layer of cotton T-Shirt material (48 threads per inch); one layer of cotton shirt material (80 threads per inch); a I0 ounce down comforter in cambric shell cover (232 threads per inch); and one layer of 13 ounce cotton denim (50 threads per inch). This simulates typical cold weather wear. The block is shot at ten feet, measured from the muzzle to the front of the block.

    test Event 3—Steel

    Two pieces of 20 gauge, hot rolled steel with a galvanised finish are set three inches apart. The steel is in six inch squares. The gelatin block is covered with light clothing and placed 18 inches behind the rear most piece of steel. The shot is made at a distance of I0 feet measured from the muzzle to the front of the first piece of steel. Light clothing is one layer of cotton T-Shirt material and one layer of cotton shirt material, and is used in all subsequent test events. The steel is the heaviest gauge steel commonly found in automobile doors. This test simulates the weakest part of a car door. In all car doors, there is an area, or areas, where the heaviest obstacle is nothing more than two pieces of 20 gauge steel.

    test Event 4—Wallboard

    Two pieces of half-inch standard gypsum board are set 3.5 inches apart. The pieces are six inches square. The gelatin block is covered with light clothing and set 18 inches behind the rear most piece of gypsum. The shot is made ten feet, measured from the muzzle to the front surface of the first piece of gypsum. This test event simulates a typical interior building wall.

    test Event 5—Plywood

    One piece of three-quarter inch AA fir plywood is used. The piece is six inches square. The gelatin block is covered with light clothing and set 18 inches behind the rear surface of the plywood. The shot is made at ten feet, measured from the muzzle to the front surface of the plywood. This test event simulates the resistance of typical wooden doors or construction timbers.

    test Event 6--Automobile Glass

    One piece of A. S. I. one-quarter inch laminated automobile safety glass measuring l5 x l8 inches is set at an angle of 45 degrees to the horizontal. The line of bore of the weapon is offset 15 degrees to the side, resulting in a compound angle of impact for the bullet upon the glass. The gelatin block is covered with light clothing and set 18 inches behind the glass. The
    shot is made at ten feet, measured from the muzzle to the centre of the glass pane. This test event with its two angles simulates a shot taken at the driver of a car from the left front quarter of the vehicle, and not directly in front of it.

    test Event 7--Heavy Clothing at 20 yards

    This event repeats test event 2 but at the range of 20 yards, measured from the muzzle to the front of the gelatin. This test event assesses the effects of increased range and consequently decreased velocity.

    test Event 8--Automobile Glass at 20 yards

    This event repeats test event 6 but at a range of 20 yards, measured from the muzzle to the front of the glass, and without the 15 degree offset. This shot is made from straight in front of the glass, simulating a shot at the driver of a car bearing down on the shooter.

    In addition to the above described series of test events, each cartridge is tested for velocity and accuracy. Twenty rounds are fired through a test barrel and twenty rounds are fired through the service weapon used in the penetration tests.

    Two ten-shot groups are fired from the test barrel, and two ten-shot groups from the service weapon used, at 25 yards. They are measured from centre to centre of the two most widely spaced holes, averaged and reported.

    Posted because it is occassionally referenced, in part or whole, even if they don't know it (for example any time ammunition makers reference peneration and expansion in gel), and there's just got a to be "a few" lurkers and forum members who aren't familiar with it.

    It is the current bench mark test in use.

    Anyone curious about their chosen load, or in the process of deciding on one, should track down the results of how it, or a comparable load, fared
    God, country, family.


  2. #2
    AEA
    AEA is offline
    Member Array AEA's Avatar
    Join Date
    Mar 2008
    Location
    North Texas
    Posts
    159
    Interesting reading...

    Now,.....give us their results with regard to current factory defense ammo......

Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. 1911 muck test VS. beretta 92 muck test videos
    By Don Glock in forum General Firearm Discussion
    Replies: 24
    Last Post: July 9th, 2010, 07:03 PM
  2. only a test
    By anotherjohndoe in forum Off Topic & Humor Discussion
    Replies: 14
    Last Post: May 22nd, 2007, 07:28 PM

Search tags for this page

fbi 1911 test

,
fbi ammo test results
,
fbi ammo tests
,

fbi ammunition test results

,
fbi ammunition testing results
,

fbi ballistic test results

,
fbi ballistics test
,
fbi ballistics test results
,
fbi ballistics testing results
,
fbi handgun ammunition tests
,
fbi handgun amunition test
,
fbi protocol ballistics test results
Click on a term to search for related topics.

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» DefensiveCarry Sponsors