New toy Sig 229 Elite

New toy Sig 229 Elite

This is a discussion on New toy Sig 229 Elite within the General Firearm Discussion forums, part of the Related Topics category; Well I got my new toy, a Sig 229 Elite in .40cal and with a 9mm Barsto barrel. It joins it stablemate a 226ST in ...

Results 1 to 12 of 12

Thread: New toy Sig 229 Elite

  1. #1
    Distinguished Member Array Colin's Avatar
    Join Date
    Feb 2006
    Location
    Vancouver, Canada
    Posts
    1,863

    Talking New toy Sig 229 Elite

    Well I got my new toy, a Sig 229 Elite in .40cal and with a 9mm Barsto barrel. It joins it stablemate a 226ST in 9mm. Needless to say I love Sigs. My wife suggested that I use a similar gun to my 226 as my backup for IPSC. Realizing her wisdom I went out and ordered the 229. I choose the .40cal version as I always wanted a 357Sig firearm, and this would give me a 3 calibre gun. The 9mm barrel still needs a bit more fitting, but it seems to work in dryfire mode. Will take it out tomorrow to shoot.

    What I have discovered from playing with it and using snapcaps.
    The .40cal/357 mags will hold 12 rds of 9mm and will feed them.
    226 9mm mags fit the gun and work fine with the 9mm barrel.
    A 9mm 226 mag will also hold 7 rds of .40cal and seems to work.
    A 229 mag will not fit a 226

    My gun has the SRT (short reset trigger) compare it to my standard 226 I am not sure what the difference is, hopefully it will showup during shooting. The SRT does require an extra step while taking the slide off. The barrel extension is to ensure compliance with Canadian laws which require the barrel be over 4” (Don’t apply logic, your brain will hurt) The barrel came standard with the gun, believe it’s from Fire dragon?? The 9mm is from Barsto. I will get the 357Sig barrel in the new year.

    Although the frame is the same width as the 9mm 226 and the slides will sort of interchange, the 229 .40cal slide is wider than the 226 9mm. It will fit my Serpa and my leather Goodrich and Gould IWB holster, but is very tight. Once the leather holster fits the 229, I suspect the 226 will be to loose. Think I will avoid the Serpa for now to minimize holster wear. The leather holster looks great with the wood grips of the 229, so it will be destined for that one I think.

    I choose the Elite because I felt it would offer an advantage with shooting the .40cal and 357 Sig, I will see if I am correct tomorrow. (If not, likely I will lie to myself for awhile!)

    Some Sig porn





    Last edited by Colin; December 8th, 2007 at 11:26 PM. Reason: spelling...


  2. #2
    Distinguished Member
    Array aznav's Avatar
    Join Date
    Jan 2007
    Location
    Harrisonburg, VA
    Posts
    1,594
    Want! Need! Absolutely gor-je-us! Wish my wife would order me to get a 40 cal Sig 229 Elite. Finally! Some porn that I can look at.


    ps. Love the grips.

  3. #3
    VIP Member Array Supertac45's Avatar
    Join Date
    May 2006
    Location
    Michigan's U.P.
    Posts
    3,657
    Sigs are great guns.
    Les Baer 45
    Sig Man
    N.R.A. Patron Life Member
    M.C.R.G.O.

  4. #4
    VIP Member
    Array Thumper's Avatar
    Join Date
    Jun 2006
    Location
    Nevada
    Posts
    7,300
    SWEET!
    ALWAYS carry! - NEVER tell!

    "A superior Operator is best defined as someone who uses his superior
    judgement to keep himself out of situations that would require a display of his
    superior skills."

  5. #5
    Member Array GotSig?'s Avatar
    Join Date
    May 2007
    Location
    Pinellas Park, FL
    Posts
    474
    Nice. I love sigs.
    كافر(Infidel)
    He who fights with monsters might take care lest he thereby become a monster. And if you gaze for long into an abyss, the abyss gazes also into you.
    Friedrich Nietzsche, Beyond Good and Evil, Aphorism 146
    German philosopher (1844 - 1900)

  6. #6
    Distinguished Member Array C9H13NO3's Avatar
    Join Date
    Nov 2007
    Location
    Texas
    Posts
    1,513
    very sexy!

  7. #7
    VIP Member Array swiftyjuan's Avatar
    Join Date
    May 2006
    Location
    Madera, CA
    Posts
    2,488
    Thanks Colin! Dang, I just fell in love again. Let us know how the other barrels work. I think I will buy the barrels now, so then I would have to find the gun to fit. Congrats on a beauty Colin!
    John
    Assault is a behavior, not a device.

    "Don't never take no shortcuts." Patty Reed, Donner Party

    Lifetime NRA member

  8. #8
    Moderator
    Array RETSUPT99's Avatar
    Join Date
    Jul 2006
    Location
    Central Florida
    Posts
    45,052

    Congrats...

    on your new toy.

    An absolutely gorgeous weapon...enjoy!

    Stay armed...stay safe!
    The last Blood Moon Tetrad for this millennium starts in April 2014 and ends in September 2015...according to NASA.

    ***********************************
    Certified Glock Armorer
    NRA Life Member[/B]

  9. #9
    Ex Member Array Ram Rod's Avatar
    Join Date
    Dec 2007
    Location
    Fayetteville, AR
    Posts
    13,687
    Very nice indeed! Congratulations.

  10. #10
    Distinguished Member Array Colin's Avatar
    Join Date
    Feb 2006
    Location
    Vancouver, Canada
    Posts
    1,863
    Well I got out on Sunday, it was -3C but clear. I ran 50xUMC and 50xBlazer 180gr through it. Not one hiccup!! The gun snaps up, but drops back down quickly, the ports and the beavertail really work well to control this gun. Wished I had brought more ammo as I was getting into the groove with this gun, have fired other .40cals, the Sig 229 feels way better, I think this gun was meant to shoot .40cal! I suspect further range reports will be typical Sig boring, gun ran well blah, blah, blah. Before I fired it, I did lube it and put a light coat of moly grease on the frame rails.

    I can’t say that I noticed a great deal of difference between my 226 with a regular trigger and the SRT on the 229, which I shot side by side, mind you my fingers were cold so that might have lessen the feel.

    I did notice that after firing often I would find insulation from the roof floating down, its 4-5’ from the gun, so a lot of energy is coming out of the ports, although I didn’t see any flame.

    The only con on this gun is that the edges of the beavertail are not bevelled, not such a problem for me, but meaty hands might notice it. I did feel one sharp edge on the wood grip against the web of my hand, so I will have to clean that up. I have noticed on some other Sig SAS guns that the grips don’t line up well, mine are pretty good, but this is one area Sig needs to pay attention to. Wood grips are going to need fitting to each gun, otherwise you will have annoyed customers.

    I really wanted to try out the 9mm barrel as I am sure it will fit. In fact I measured the barrel sections on both barrels where they pass through the frame and they are both the same size, although I suppose the chamber/barrel hood fit effects the lineup of the barrel?

    Next shoot I will try out .40cal in my sig 226 9mm mags to see how it works. I know it works with snap caps.

    The gun did seem to shoot low, but not sure if it was me or the gun, will have to shoot more. I suspect that the nite sights are a bit taller than the standard sights and they seem to want to be put over the POA not under it.

  11. #11
    Distinguished Member Array Colin's Avatar
    Join Date
    Feb 2006
    Location
    Vancouver, Canada
    Posts
    1,863
    So I got my 229 out to the ranges a few times. I love shooting this gun. The .40cal barrel from fire dragon is very accurate, but it seems the 9mm Barsto barrel seems to shoot low. I will have to borrow a pistol rest to figure out exactly where it is shooting at.

    So far I have fed it 180gr FMJ .40cal from Blazer, UMC, Lawman and 180gr TMJ reloads with 4.1grs of titegroup. Also started shooting some 170gr SWC reloads out of it as well. Absolutely no problem with the above ammo. I haven’t had a chance to get any JHP so that will have to wait for a bit.

    The 9mm has been a bit of a mixed story. All commercial ammo, (winclean, fiochi, Remington. 124gr I have used has fed flawlessly through it, using both the 229 .40cal mags and 9mm 226 mags. However I have had some FTE/stovepipes using reloads. My reloads use 3.9-4.1 grs titegroup behind 124gr TMJ, FMJ and RN lead. I suspect this load is to light for the .40cal springs. I will beef up the load a bit to see if this resolves the problem. I also found the chamber of the Barsto barrel to be unforgiving. I had some 9mm reloads that were very cranky, they gave me problems in most guns except for my 226, the 229 was no exception, it didn’t like them either.

    I also shot a variety of 9mm JHP, Golden Sabres, Hydro-shocks and Remington green box JHP through it. It gobbled them all up and wanted more.

    The nite sights are quite nice to use and was shooting in the dark with them the other night. Shooting the 9mm fiochi out of the 229 barrel is quite fun, the fireball is sort of like that out of a 7.62 Tork.

    Issues

    I have been having a problem with the slide not locking back, as I suspected it was my thumb working it’s way up, the wood grip don’t protect the slide lock as well as the Hogues grips does. I will have to correct my hold for this.

    Frame finish
    This pisses me off, the finish on the frame is easily scratched, one would think that on a high end gun they would try to find something that would stand up to normal use.

    Accessory rail
    ##$%#% SIG!! This rail is friggin tight on my MX3 light, it will barely slide on, plus the bottom of the rail is convex and interferes with the cross bar on the MX3. This light works fine on my 226ST, SW M&P and other guns. How could Sig screwup something so simple? It is an absolute bugger trying to get it on and off.

    SRT
    Maybe my fingers are dumb but I don’t seem to be able to tell the difference between this gun and my stock 226

    Holsters
    I looked at the Safariland holster for this gun and liked the protective material inside, but could not get into the thumb release. So I went with the Blackhawk Serpa that I am used to. I have them for both my 226 and M&P and like them quite a bit. However this particular design leaves something to be desired. Unlike the M&P version, there is no trough for your finger to follow after releasing the lock. Instead there is a pronounced outward lip to protect the leading edge of the grip. This foces your finger to grate against the raised edge of the holster. It needed sanding to prevent rasping the finger. I realize it’s hard to design a holster to meet every gun, but I think they went the cheap route on this design. It is revision #9 of this one, hopefully #10 will be better. My leather Gould & Goodrich IWB holster for my 226 barely fits this and would overstretch it if I tried to use it as the slide on the 229 is thicker than the 226.

    Summary
    I not ready to use this as my go to gun yet, the POI needs to sorted out, need to try it with .40cal JHP and the inability to easily fit a light to it, makes it mainly a range gun for now. Hopefully I can resolve all of the above.

    The finish issues really peeves me and I wished now that I had gotten a stainless Elite instead. When I do buy a 220, it will be Stainless. I do like the Beavertail for the .40cal as it aids the gun in dropping back into it’s slot after recoiling. Likely will get the Elite Stainless 220 in .45acp if possible.

  12. #12
    Member Array jarhead45's Avatar
    Join Date
    Dec 2007
    Location
    Las Vegas
    Posts
    191
    Excellent report. I was thinking of doing the SRT on my P6 but I may hold off now and put the money into some better sights.
    Honor, Courage, Virtue. These are what makes a man.
    "The Marines I have seen around the world have the cleanest bodies, the filthiest minds, the highest morale, and the lowest morals of any group of animals I have ever seen. Thank God for the United States Marine Corps."
    Eleanor Roosevelt, 1945

Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. FP-10 Lube Elite????
    By TJK68 in forum Defensive Carry Guns
    Replies: 8
    Last Post: July 26th, 2010, 01:21 PM
  2. New Delta Elite...
    By Sarge45 in forum Defensive Carry Guns
    Replies: 19
    Last Post: July 30th, 2009, 10:35 PM
  3. sig 229 elite dark (9mm)
    By jwalker497 in forum Defensive Carry Guns
    Replies: 0
    Last Post: May 4th, 2009, 12:05 AM
  4. P229 Elite
    By Phantomoak in forum Defensive Carry Guns
    Replies: 9
    Last Post: February 14th, 2009, 02:35 PM
  5. Stack-On ELITE 36
    By Magilla82ABN in forum Related Gear & Equipment
    Replies: 0
    Last Post: April 7th, 2008, 03:25 PM

Search tags for this page

226st 40 cal stove pipe
,
229 elite
,
does a p229 shoot a 40
,
does sig p229 elite need snap cap
,
sig 229 stovepipe new
,
sig p229 elite stainless 40 shooting
,
sig p229 elite stovepipes
,
sig saucer 40cal229elite
,
sig stainless elite bar-sto
,
snap caps needed for p 229?
,
what do you shoot in your 40 cal 229 elite
,

why would sig 229 stovepipe?

Click on a term to search for related topics.