Checking The 1911 Extractor - A PIC.

This is a discussion on Checking The 1911 Extractor - A PIC. within the Reference & "How To" Forum forums, part of the Related Topics category; Checking The Extractor. First of all your extractor should be held firmly enough by the firing pin stop so that it cannot "clock" or rotate. ...

Results 1 to 3 of 3

Thread: Checking The 1911 Extractor - A PIC.

  1. #1
    Administrator
    Array QKShooter's Avatar
    Join Date
    Dec 2004
    Location
    Off Of The X
    Posts
    34,585

    Post Checking The 1911 Extractor - A PIC.

    Checking The Extractor.

    First of all your extractor should be held firmly enough by the firing pin stop so that it cannot "clock" or rotate.
    If it will "clock" even slightly then you should buy an oversize FP Stop at the same time you're shopping for a high quality tool steel machined from bar-stock extractor. Check Brownells. There are many available these days.

    The only aftermarket extractor that I would stay away from would be the EGW - while the EGW (fully machined from bar-stock) aftermarket 1911 parts (like their slide stop, thumb safety, and ejector) are some of the very best ever produced for the 1911...their extractor design fully sucks big time.
    Just one mans opinion on that.


    Please keep in mind that this is with a high quality aftermarket "tool steel" machined from bar-stock extractor.

    Remove your slide from the frame and slip your desired carry round up into the extractor.

    > The rear of the case head should be able sit flat (or almost lay flat) on the slide breech face.
    A very slight even hair-line of light showing between the rear of the case head and the breech face is acceptable.
    The vast majority of incorrectly "factory fit" extractors will not permit that to happen.

    > Ideally....The "Hook" of the extractor should not contact the cartridge case in the cannelure area of the case.
    Notice in my photo that there is daylight showing in the space between the extractor claw and the case cannelure and the case head is flat on the breech face.
    There does not have to be a LOT of light showing but, the extractor claw should not be cutting into the cartridge case or forcing the case up off of the breech face.

    > The cartridge should be held against the slide breech face in the milled cut - with pressure applied to the case head by the FLAT of the extractor...not the extractor hook.

    The function of the extractor on a 1911 (these days) basically just holds the fired cartridge case in position to be whapped hard by the ejector.
    Now that wartime STEEL Case ammo is no longer being used the 1911 extractor does not need to forcibly YANK the fired cartridge case out of any modern highly polished & decently smooth barrel chamber.

    > Slipping a round of ammo up into the extractor with the slide held horizontally - the cartridge should remain horizontal until the front of the slide is tapped - then the round should drop down by gravity and the weight of the bullet.
    That is pretty much the correct tension IF everything else is 100% correct.

    > The "FLAT" of the extractor should be smooth and slightly rounded at the bottom of the flat so that the case head slips perfectly up into the extractor during the feed cycle.

    > Ideally.........in a fully assembled pistol the cartridges SHOULD still feed from the magazine into the barrel chamber when the slide is eased forward as slowly as possible.

    You should be able to insert a loaded magazine into the pistol - hold the pistol upside down and the cartridges should still feed.

    I should ADD that there are 1911 pistols with extractors that are differently configured and "fit" ~ and they WILL still feed and cycle with great reliability.

    BUT, if your personal 1911 will NOT feed perfectly then some of the above is probably WHY.


  2. Remove Ads

  3. #2
    VIP Member Array rodc13's Avatar
    Join Date
    Jun 2006
    Location
    San Antonio, Texas
    Posts
    2,753
    Thanks for this excellent tutorial, QK!

    Perhaps this should take up permanent residence in the Reference and "How To" Forum?
    Cheers,
    Rod
    "We're paratroopers. We're supposed to be surrounded!" Dick Winters

  4. #3
    Administrator
    Array QKShooter's Avatar
    Join Date
    Dec 2004
    Location
    Off Of The X
    Posts
    34,585
    Note that the above pistol in my PIC does not have an opened up and lowered and relieved ejection port OR an extended ejector or a throated barrel...or a highly polished frame feed ramp...and it feeds/functions perfectly with hollow points fed from Government Surplus Nam era "Mil Spec" "Assy" magazines.

Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Checking The 1911 Extractor - A PIC.
    By QKShooter in forum Defensive Carry Guns
    Replies: 14
    Last Post: December 13th, 2009, 03:57 PM
  2. S&W Extractor Rod
    By wjh2657 in forum Firearm Cleaning & Maintenance
    Replies: 2
    Last Post: September 26th, 2009, 05:01 AM
  3. Para power extractor on a Springfield 1911?
    By 17679 in forum General Firearm Discussion
    Replies: 4
    Last Post: December 20th, 2008, 04:09 PM
  4. 1911 extractor damage/breakage?
    By dustoff451 in forum Defensive Ammunition & Ballistics
    Replies: 1
    Last Post: September 13th, 2007, 10:53 PM

Search tags for this page

1911 ejector
,

1911 extractor

,
1911 extractor claw
,

1911 extractor clocking

,
1911 extractor function
,
1911 extractor tool
,
1911 extractors
,

best 1911 extractor

,
best aftermarket 1911 extractor
,
best extractor for 1911
,
extractor clocking
,
extractor clocking 1911
Click on a term to search for related topics.