Lathe Turned 1911 Grips

This is a discussion on Lathe Turned 1911 Grips within the Related Gear & Equipment forums, part of the Defensive Carry Discussions category; [B]I just remembered that (way back when) I said that I would post pictures of my jigs that I used for lathe turning perfect 1911 ...

Results 1 to 4 of 4

Thread: Lathe Turned 1911 Grips

  1. #1
    Administrator
    Array QKShooter's Avatar
    Join Date
    Dec 2004
    Location
    Off Of The X
    Posts
    35,276

    Lathe Turned 1911 Grips

    [B]I just remembered that (way back when) I said that I would post pictures of my jigs that I used for lathe turning perfect 1911 grips.
    It's VERY possible to duplicate the Colt factory grips EXACTLY by turning them. Minus the checkering of course.

    By The Way....I always do everything I say I'm going to do....eventually. One "thing" always gets pushed in front of another (with me) & it takes me a while to do what I intend to do. Finally...here are the photos. My Digital Camera is ready to die...so the pics slightly suck.

    If you are really into lathe working you should be able to just look at my photos & take it all from there.
    Shown mounted on the jig is the first set of MAPLE test GRIPS that I made. I turned a few sets of Elephant Ivory grips & a few in Snakewood & Ebony & then never made any more grips.
    I get bored with "stuff" in a hurry.

    I made the grip jig about a decade ago out of Hard Rock Maple. (a bowling alley floor that was being ripped up)
    You (obviously) need to profile the grips out first. They were bandsawn out close to the line & I used a small drum sander (in my drill press) to get the final profiles perfect.

    Hole sizes and hole spacing are critical.
    Below those Maple jig photos are pics of the adjustable brass jig that I made to get the hole spacing perfect by using a factory grip as a master. It's NOT PRETTY but, it works.

    The extra hole is for the COLT medallion location.
    The brass drill guides make drilling the bushing holes easy & you'll also need to turn exactly fitting holdins pins to keep everything Kosher & perfectly lined up.

    The screw hole recesses for the little grip screw bushing flange & the Grip Screw recess countersinks are done using another really simple set~up that is hiding SOMEWHERE in my basement.

    BTW ~ I don't have any formal training in machine work or lathe work (other than High School Machine Shop)...so if I can do it then you sure can also.

    Oh...& milling the rear notch for the plunger tube was done while the material was still in flat slab form & I just marked that off & did that by eye using a carbide cutter also on the drill press.

    ENJOY! Maybe this will be a good winter project for some forum member.


  2. Remove Ads

  3. #2
    VIP Member Array Bud White's Avatar
    Join Date
    Dec 2004
    Location
    Away - Health Problems
    Posts
    17,353
    Looks like you put a lot of ork into it QK im deff nto a wood worker so i wont be making any grips anytime soon neat pics though

  4. #3
    Assistant Administrator
    Array P95Carry's Avatar
    Join Date
    Mar 2005
    Location
    South West PA
    Posts
    25,482
    Excellent QK - thx for all the pics - which are actually just fine.

    As an engineer and machinist I can say that you have things well covered here - pretty much what I reckon I'd do to achieve those results. Once the radius of the grip panels is established then the jig design sorta speaks for itself - tho that said, making the jig is quite a chunk of work too.

    Many years back I think I derived as much pleasure as anything from making jigs, fixtures, special tools etc - as actual work on the lathe. This was metal of course but, my wood lathe has seen some occasional use too as a hobby.

    Nice work Sir
    Chris - P95
    NRA Certified Instructor & NRA Life Member.

    "To own a gun and assume that you are armed
    is like owning a piano and assuming that you are a musician!."


    http://www.rkba-2a.com/ - a portal for 2A links, articles and some videos.

  5. #4
    Member Array d2thomas's Avatar
    Join Date
    Oct 2005
    Location
    Kalamazoo, Michigan
    Posts
    275
    Hey I say you can only learn one way - by doing.

    It looks like you got a great start, I like what I see!
    Maybe we can have you make some custom "Combat Carry Member" 1911 grips? They'd be all the rage!
    S&W 5906
    ********
    si vis pacem, para bellum

    protego communis bona

Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Planning on getting a lathe...
    By automatic slim in forum General Firearm Discussion
    Replies: 5
    Last Post: July 2nd, 2010, 11:16 AM
  2. New Grips! VZ for 1911
    By rocky in forum General Firearm Discussion
    Replies: 5
    Last Post: March 7th, 2010, 04:57 AM
  3. New grips for the 1911! (pic)...
    By Smitty908 in forum Concealed Carry Issues & Discussions
    Replies: 18
    Last Post: October 1st, 2007, 03:01 PM

Search tags for this page

1911 grip fixture
,

1911 grip jig

,
1911 grip jigs
,

1911 grip making jig

,
1911 grip panel jig
,
1911 grip panel jigs
,
1911 grip screw spacing
,
1911 grips jig
,
how to make 1911 grips
,
make 1911 grips
,

making 1911 grips

,
router jig for 1911 grips
Click on a term to search for related topics.