action bar assembly wobble???

bryman · October 18th, 2009, 11:51 PM

so i put a new forend on my pardner pump. but now i notice a slight amount of action bar assembly wobble. is this OK? the forend is on quite tight. but it seems now since i put a forend grip on there is the wobble maybe i just didn't notice it with the stock grip on due to its ridiculous length? the pic below outlines what im talking about. sorry for large size.

this is a pic of the whole setup so far..

movieguns · October 19th, 2009, 12:01 AM

I'll bet the wobble is from side to side rather than up and down which may indicate twisting or binding of the bar(s) in the channels. Usually, the installation of a vertical foregrip accentuates this because we have a tendency to twist our hands as we cycle the action. Use a good quality grease (not oil) in the channels and that should take up a lot of the slack. If not, remove the forend and check to see if the action bars are bent or out of true.

Ram Rod · October 19th, 2009, 05:50 AM

Not much of a problem really. Aftermarket stuff is designed to fit a wider range of models most times. The slack means the inside diameter of the fore end is larger than it needs to be. I have a ProMag tri-rail fore end I would have sold you cheap had I known.

C hawk Glock · October 19th, 2009, 11:39 AM

Not to be rude, but your aftermarket parts cost more then your rig! haha. It looks pretty cool.

varob · October 19th, 2009, 12:02 PM

Looks nice.

I love after market parts. My 870 is loaded down with them.

bryman · October 19th, 2009, 03:18 PM

Quote:

Originally Posted by C hawk Glock

Not to be rude, but your aftermarket parts cost more then your rig! haha. It looks pretty cool.

true but i didnt pay for the gun so hehehehe my pal owed me money for helping him out at his new house so it was kinda free money

October 18th, 2009, 11:51 PM	#1
bryman Member Join Date: Sep 2009 Location: Henderson, Colorado Posts: 58	action bar assembly wobble??? so i put a new forend on my pardner pump. but now i notice a slight amount of action bar assembly wobble. is this OK? the forend is on quite tight. but it seems now since i put a forend grip on there is the wobble maybe i just didn't notice it with the stock grip on due to its ridiculous length? the pic below outlines what im talking about. sorry for large size. this is a pic of the whole setup so far..

October 19th, 2009, 12:01 AM	#2
movieguns New Member Join Date: Oct 2009 Location: California Posts: 12	Action Bar Wobble I'll bet the wobble is from side to side rather than up and down which may indicate twisting or binding of the bar(s) in the channels. Usually, the installation of a vertical foregrip accentuates this because we have a tendency to twist our hands as we cycle the action. Use a good quality grease (not oil) in the channels and that should take up a lot of the slack. If not, remove the forend and check to see if the action bars are bent or out of true.

October 19th, 2009, 05:50 AM	#3
Ram Rod VIP Member Join Date: Dec 2007 Location: crawford county, arkansas Posts: 8,807	Not much of a problem really. Aftermarket stuff is designed to fit a wider range of models most times. The slack means the inside diameter of the fore end is larger than it needs to be. I have a ProMag tri-rail fore end I would have sold you cheap had I known. __________________ RamRod-----sans remords live, eat, breathe, sleep Glock

October 19th, 2009, 11:39 AM	#4
C hawk Glock Member Join Date: Jun 2009 Location: W. Washington Posts: 336	Not to be rude, but your aftermarket parts cost more then your rig! haha. It looks pretty cool. __________________ Thank you sir, may I have another?

October 19th, 2009, 12:02 PM	#5
varob Distinguished Member Join Date: Jun 2009 Location: Virginia Posts: 1,273	Looks nice. I love after market parts. My 870 is loaded down with them. __________________ Don't believe what you hear and only half of what you see! -Tony Soprano

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode