Cupcake

I mean the COL. Using my lee classic turret, some of the 9mm rounds I made were coming out a bit longer than desired. Definately pressing the lever all the way, even checked length, put the round back, and hit it again. Some just like to be longer. What am I doing wrong?

__________________
Pain is temporary, quitting is forever.


www.zerotoathlete.blogspot.com
My journey to fitness.

fatboy97

I use a Dillon 550B, so I can only tell you what I do.

I usually check at the beginning and then every 50 or so rounds and found a variance of only .005, so I now set my COL to be .005 below max just in case they get a little long. I've never seen any more than .005 from what I set it up to start with, and not had one issue with any of those at the range.

__________________
Be Observant and Be Safe.

Current Collection: Glock G26, G19, G23C, SIG P226-40 TT, Ruger GP-100, and 22/45 MKII
Former Collection: Taurus 92SS, SIG P220 TT, S&W 360, SIG P239-40

houdini

after I make my rounds I put them in a gauge to see how they look. I have no problem with them.

DMan

I use the 550B as well, however I have seen some other presses have similar issues. Check to make sure that there is no "junk" build up (powder, or other stuff) that happens to get under the shell. I frequently use a canned of compressed air (like what is used on computer keyboards) to blow out the corners and quickly assure that the nothing is going to hinder the bullet or casing. Also blow you the inside of your dies occasionally. I was surprised at one time when I was having issue with seating depth, and I found a small amount of "crude" built up inside the die. I blew it out, and everything fell right back into line. Any buildup like I experienced causes bullets to seat deeper (brass sits up higher, or the bullet is pressed lower down into brass).

If your having an issue with variances going long check you dies, tighten them up if necessary, any "play" or anything that "wiggles" should be double checked to determine if it is going to affect the seating.

Also, are you using the same bullets? or are they different make? Stay consistent. A bullet from different companies or in different styles will seat differently. Select one make/style and do set your dies to that. If you change bullets, you will need to readjust the dies.

__________________
If guns cause crime, then forks made Rosie O'Donnell fat!!

Rosie - Say bye bye: You aren't much of a View anymore! Your true colors have been shown, and they are not Red, White, and Blue!

Cupcake

Thanks guys. The bullets are all from the same batch. (actually, I noticed it with both calibers: .380 with fmj round nose, and 9mm with lead round nose. I was hoping to get a chance to make some, because to be honest, I can't recall what the spread was. I wanna say some were .01 off, but I fired everything I made. (real new, so I'm only making small batches to test).

What's your opinion on how much variation is too much?

__________________
Pain is temporary, quitting is forever.


www.zerotoathlete.blogspot.com
My journey to fitness.

dukalmighty

.01 isn't that much and I have had variations, like others have said as far as cast bullets sometimes if they shave lead and or lube when seating the bullet it will gum up the die and start seating bullets deeper etc.As long as it's in that range I wouldn't worry just make sure you don't go under the minimum coal or over the maximum

__________________
I like Poetry,Long Walks On The Beach,And Poking Dead Things With A Stick

autofix

Sounds like something's coming loose on you, die, turret, etc.. If something were building up, then your rounds would come up shorter not longer. You should always ck your dies and all mechanical parts of your rig for loose parts and movement - if it's got moving parts it can wear or come loose. If it's new the parts all need to say "hi" to one another and you'll get some minor discrepencies in col or perhaps bullet seat or crimp. My Dillon has things you have to keep an eye on, I guess they all have a personality that you get to know after awhile. Kinda like a new wife or girlfriend.

__________________
LIVING IN A PLACE WHERE YOU HAVE NO "DUTY" TO RETREAT AND MAY MEET FORCE WITH FORCE

dukalmighty

That's true unless you adjusted OAL with a gummed up die that was stuck in a lower position but while seating bullets the pressure caused it to move up,then your OAL would increase

__________________
I like Poetry,Long Walks On The Beach,And Poking Dead Things With A Stick

Cupcake

Dunno. New dies, turret. I'm wondering if its just poor bullet manufacturing quality management. I say this because several would be right on, within .003 or so, then one would be long, then the next would be perfect...

Stuck at work today (not really, voluntary OT for Doubletime:)), so I can't load any now. I do believe It was way more pronounced with the 9mm cast bullets that I got from a gun show. Maybe the guys' molds aren't all exactly the same?

__________________
Pain is temporary, quitting is forever.


www.zerotoathlete.blogspot.com
My journey to fitness.

celticredneck

Using my old Lyman Spartan press, and assorted dies, depending on caliber, I set my dies for each bullet type that I'm loading with a "dummy pilot round" These are loaded with the first bullet out of a box.and seated in a sized and trimmed case, but without powder or primer. After seating I measure each pilot round and then store it in a labeled drawer, showing cal. and bullet by weight, type and manufacturer. When I go to set up my seating die for that cal. I loosen the seating die, run the press down to full stroke, than adjust the seating die to just where it is firm on my pilot round. My lengths have been pretty consistent over the 10 or so years that I have been reloading.