Sergeant Mac

I'm getting a bunch of stuck cases while decapping/resizing .223 brass.

Here's the lowdown:

Lee Classic Turret Press with 4-hole conversion
Lee .223 full-length resizing die
Assorted once-fired brass (manufacturer doesn't seem to matter)

Laid out about 80 tumbled cases on newspaper and sprayed them from the mouth end with One Shot, rolled them around, and let them dry for 30 minutes.

decapped/resized about 30 cases with no problems whatsoever.

STUCK CASE! Pulled right out of the shellholder, mangling the rim of the case.

Read instructions and kinda-sorta followed them. Loosened decapping pin collar, and it came right off the pin, which was hopelessly stuck in the case. Whacked the top of the pin with a hammer until the case came out. Pin still stuck in case. Cut neck off of case with wirecutters, removed case, pulled neck ring off of top end of pin.

Next case was uneventful. (but I think I bent the decapping rod a little)

Next FIVE cases got stuck. After the first, I sprayed One Shot up into the die.

I gave up.

Any ideas what's causing this, and how to fix it? I'm considering buying a carbide FL sizing die, but as near as I can tell, only Dillon makes them, and they're damned proud of theirs, to the tune of $100+.

Impax

I also use One Shot when sizing .223 cases. What I've found to help is to shake the can every time I use it to make sure it is mixed well. If that doesn't work, polish the decapping rod with 1000 grit sandpaper, and switch to imperial sizing wax like I did. I have not stuck a case with it yet sizing .308. I did stick .308 cases with oneshot.

__________________
Texas Citizens Defense League©

http://txcdl.org/

dukalmighty

I have had a few cases that seem to be harder to resize than other cases,what i do is force it in the die a little then back it out then force it in a little more then back it out a little at a time til i resize the whole case,I'm thinking the brass may be 5.56 military brass which has thicker case walls

__________________
I like Poetry,Long Walks On The Beach,And Poking Dead Things With A Stick

Beans

I just finished decapping/sizing 200 .233 cases, none stuck.

I set the cases on the rim and spray One Shot on all sides including the case mouth.

I then size & decapp while the cases are still damp from the One Shot
No waiting-no rolling- No stuck cases

Jeff F

I would put my money on a bad die. Some are rougher than a cobb and will cause all kinds of problems. Had a Lyman 357 sizing die like that once. You can try to polish the inside of the die body or try to get it replaced and see if the problem goes away.

__________________
"Those who would give up essential liberties for a little temporary safety deserve neither liberty or safety" -Benjamin Franklin-

Mtbiker

Your die probably has a scratch. Check it and spring for a carbide sizer. I like the Dillon spray better then the one shot also.

__________________
-Biker

stargzer

[quote= I'm considering buying a carbide FL sizing die, but as near as I can tell, only Dillon makes them, and they're damned proud of theirs, to the tune of $100+.[/QUOTE]

I'm using the Dillion .223 FL Carbide Die, with this die you must still lube your cases. I use Dillions case lube, works great. The carbide die will last longer if you reload alot and give your cases a little better shine. I must say Dillion may be a little higher in cost, but they always work and they have a "No B.S. lifetime warranty".

Stargzer
Ret. USAF MSgt.
NRA Life Member

Jay6

I had this same problem with my first .223 setup I used to use. I actually took a q-tip with lube on it and ran it around the inside of the neck a little bit after lubing the outside. I found this to help a great deal. Good luck!

Tubby45

You still need to lube with carbide dies. They are designed for commercial loading to reduce wear on the dies. For the casual reloader they are a waste of money.

I use Lee .223 dies and HOS (Hornady One Shot) lube. Roll them on a lube pad and you're set.

Do a "shake and bake". Put a bunch of brass in a big bag. Spray a bunch of lube in there. Close it up and shake it all around. Lubes the cases just fine.

Usually stuck case means not enough lube.

__________________
Freakshow Manufacturing LLC
"You can kill it. We can help."
07 FFL/ 02 SOT

MajorDude

Try some Imperial Sizing Die Wax. That's all I use anymore. A tin lasts forever, you don't have to breathe it and it keeps your hands baby soft!