|
|
|
|||||||
| Register | Forum Rules | FAQ | Members List | Calendar | Mark Forums Read |
| Forum Donations | DefensiveCarry Store | DefensiveCarry Gallery | USGO Gallery | Related Links | Forum Help & Extras |
| Reloading DefensiveCarry.com accepts no liability for reloading information posted by members. It is down to the individual posting to ensure safe standards and to readers to verify what they read - it is they finally who bear responsibility for useage of information. Remember - typos can occur! We strongly recommend that in most cases quoted loads be derived from recognized loading manuals and if possible these should be referenced. Where loads do not have back-up reference data available, for instance with use of an unusual powder, then posters are asked to please detail their method for establishing their data. Irresponsible publishing of unsubstantiated ''guestimated'' data is deprecated and may be heavily moderated. |
 |
|
|
Thread Tools | Display Modes |
October 27th, 2009, 05:52 PM
|
#11 |
|
Member
 Join Date: Oct 2009
Location: Atlanta
Posts: 17
 |
Two things: 1.) As a follow-up to what Majorlk said, if the bullets are crimped or lacquer sealed (think military .45 ACP ball ammo, you can break the seal by running each round through a reloading press with the seating die in, set just low enough to push the bullet into the case slightly to break the seal. After that, use the bullet puller and bang away and you'll get the bullet out much more easily. 2.) I put a cotton ball in the bottom of the tube, to save the point of spitzer-type rifle bullets. Works well. This is not much of a factor with pistol bullets, though.
Last edited by pollardjd; October 27th, 2009 at 05:53 PM.. Reason: Corrected grammar and typos |
|
|
|
October 27th, 2009, 08:41 PM
|
#12 |
|
Member
 Join Date: Mar 2007
Location: NJ
Posts: 393
|
The pulled is for when I press a bullet in to far while re-loading.
|
|
|
|
|
October 28th, 2009, 11:18 AM
|
#13 | |
|
Senior Member
 Join Date: Jun 2009
Location: Naugatuck, CT
Posts: 843
|
Quote:
__________________
An armed society is a polite society. Manners are good when one may have to back up his acts with his life. - Robert A. Heinlein |
|
|
|
|
|
October 28th, 2009, 12:00 PM
|
#14 | |
|
Member
Join Date: Mar 2007
Location: NJ
Posts: 393
|
Quote:
|
|
|
|
|
|
October 29th, 2009, 11:32 PM
|
#15 |
|
VIP Member
 
Join Date: Feb 2006
Location: Parts Unknown
Posts: 2,492
|
smack it.
__________________
An armed man is a citizen. An unarmed man is a subject. Red State State of Mind |
|
|
|
|
October 30th, 2009, 11:27 AM
|
#16 |
|
Member
Join Date: Oct 2009
Location: Mississippi
Posts: 337
|
What Pollardjd said about using the seating die to push the bullet in a little can be a big help. Don't ever try to pull rim fire bullets.
__________________
Glock 22, GP100, S&W mod 60, Colt Delta Elite, Colt Govt 380, Ruger Single Six, Ruger Bearcat, Colt New Police |
|
|
|
|
October 31st, 2009, 04:53 PM
|
#17 |
|
Member
Join Date: Mar 2007
Location: NJ
Posts: 393
|
Finally did got around to using the puller this morning. Worked like a champ. Thanks
|
|
|
|
|
October 31st, 2009, 06:06 PM
|
#18 | |
|
Senior Member
Join Date: Jun 2009
Location: Naugatuck, CT
Posts: 843
|
Quote:
__________________
An armed society is a polite society. Manners are good when one may have to back up his acts with his life. - Robert A. Heinlein |
|
|
|
|
|
October 31st, 2009, 11:24 PM
|
#19 |
|
Distinguished Member
Join Date: Dec 2004
Posts: 1,694
|
No danger of firing the round, but if I have many bullets to pull I much prefer the collet type. It is faster and takes less effort. I second the advice to adjust the seater so that the bullet is moved if pulling from military rounds.
I wouldn't be without both a kinetic puller and a collet puller. Regards, Jerry |
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
