Defensive Carry banner

1 - 13 of 13 Posts

·
Registered
Joined
·
55 Posts
Discussion Starter · #1 ·
Currently loading for .357/.38. Later I will get Dies for .44spl/.44mag

Lee Single Stage Breech Lock Challenger Press - Check
Lee Carbide 3 die set .38spl/.357 - Check (currently enroute via Midsouth Shooters)
Lee Perfect Powder Measure - Check
Lee Dipper set - Check
Frankfort Arsenal Caliper - Check
Frankfort Arsenal Scale - Check
Lee Case Conditioning Kit - Check
Lee Shell Length Gage w/shell holder - Check
Hornaday One-Shot Case Lube - Check
Heavy Duty Work Bench - Check
Lee Breech Lock Die Inserts (total 7) - Check
Lee Modern Reloading 2nd Ed. - Check
Hodgon Reloading Guide - Check
Funnel - Check

Shell Holder Plate - MIA
Primer tool - MIA

Am I missing anything else?:INBath2Urinal:
 

·
Premium Member
Joined
·
8,833 Posts
Brass, bullets, powder and primer?

The more experienced re-loaders* can chime in on the other stuff, if any.

*My reloading press is the Internet and my credit card. (Belated welcome to the forum, by the way).
 

·
Super Moderator
Joined
·
19,938 Posts
How do you plan to prime your cases?

Do you have some cartridge trays to hold your ammo while it's in process?

At some point you may have a goof-up and you'll need a kinetic bullet puller to disassemble your loads, but that can wait.
 

·
Registered
Joined
·
42,987 Posts
You won't need to lube the cases with carbide sizing dies, and I've read too many horror stories involving OneShot spray lube and stuck cases.

Got a solid bench to work on? The most important thing(s) is to follow the load tables and avoid interruptions. Reloading is simple, although it can sound intimidating. Take it step by step and develop a routine. Consistancy is your aim, not speed.

Enjoy!
 

·
Registered
Joined
·
55 Posts
Discussion Starter · #5 ·
Yes, I have a Kinetic hammer. No reload treys (however I think my .38/.357 shells will sit upright when placed in old .44 factory ammo treys). As far as primers, not sure how I'll work that in without a tool, but I've been using the Lee Loader kit and haven't had a problem priming my brass... So I hope I can get started once my dies show up.
 

·
Registered
Joined
·
55 Posts
Discussion Starter · #6 ·
Oh, another question... For those of you who are right handed, is there a preferred side of the bench that you prefer to mount your press on?
 

·
Super Moderator
Joined
·
19,938 Posts
Look into the hand priming tools... I know guys who prime their sized brass while watching TV.

I'm a righty, and I mounted my progressive on the right side of my bench. I have my trays of brass and box of bullets on my left. Not sure about the Dillons or other progressives, but viewed from above you start with an empty case at about 10 o'clock on the Hornady AP, and the sequence runs CW.
 

·
Registered
Joined
·
7,093 Posts
I mount mine in the center so that I can pull the lever with either hand. I mostly use a single stage press and Ill prep 1000 cases at a time. Then prime and seat bullets as needed. So Ill do 100 or so and switch hands. DR
 

·
Registered
Joined
·
32 Posts
I use One shot on ALL my pistol brass and I have carbide dies. It makes the process easier the amount of force is less and the press runs smoother. People who get stuck cases with One Shot are also using rifle brass and typically are not using it right. If you get a straight wall pistol round stuck you are doing something completely wrong. Take a gallon zip lock bag with about 1/2 full of brass and spray a few shots of One shot, then shake and allow to sit for about 5 mins.

Am a right handed and my Dillon 650 is mounted on the far left side of the bench, I also sit when reloading.

Accurate and Western powders have a nice reloading guide on their website, I printed off both versions and placed them in a 3 ringed binder.
 

·
Registered
Joined
·
55 Posts
Discussion Starter · #11 ·
Very cool guys. I guess I won't sweat the mounting location of my press. I can see how all right handers might have different preferences.

I've used the One Shot Case Lube on all my pistol brass and have not complaints. I've only reloaded with the Lee Loader and my trusty rubber mallet, so that is all I can speak for.
 

·
Super Moderator
Joined
·
19,938 Posts
I use One Shot for lubing rifle brass, but it leaves an film which I'd rather not deal with. I see no reason to lube pistol cases being sized in carbide dies - never had a stuck one yet.
 

·
Registered
Joined
·
915 Posts
I see no reason to lube pistol cases being sized in carbide dies - never had a stuck one yet.
I have run tens of thousands of pistol and revolver cases through carbide resizing dies without any sort of lubricant. Lubricant isn't needed for pistol or revolver cases with resizing carbide dies.
 
1 - 13 of 13 Posts
Top